[LINK]: Com 521 Software V1.0

[segaauto]

I need Com 521 Software V1.0 or V1.1
Can somebody help me.

An advance thanks

[monty_burns_007]

is that for the basic card CP521 BASIC ? (103U / 95U)
If so you can transfer the program to the CP through hyperterminal and put the card in run also there....

[segaauto]

is that for the basic card CP521 BASIC ? (103U / 95U)
If so you can transfer the program to the CP through hyperterminal and put the card in run also there....

YES it is for CP521 Basic....How can I transfer the program with Hyperterminal????? if you can help me I will Appreciate it a lot.

In advance Thanks.

segaauto

[monty_burns_007]

connect to the 25pin serial port of the CP521 through a null modem cable (2 and 3 crossed).
put the CP521 in stop, if it is running, put the switch on CP521 in stop.
Then start and stop the PLC (run switch).
Open hyperterminal 9600 N E and press space.

You get a READY prompt.
Load you basic program through Hyperterminal File Send Text file.
After the program is transferred enter: PROG1
and then RUN

that's is !

monty

[Link]

Hello ,

COM521 Basic V1.1 english,

you can download here: http://shareplace.com/?CFD358516
or
http://plcforum.uz.ua//S5PEC21X.rar

Greetz

[segaauto]

connect to the 25pin serial port of the CP521 through a null modem cable (2 and 3 crossed).
put the CP521 in stop, if it is running, put the switch on CP521 in stop.
Then start and stop the PLC (run switch).
Open hyperterminal 9600 N E and press space.

You get a READY prompt.
Load you basic program through Hyperterminal File Send Text file.
After the program is transferred enter: PROG1
and then RUN

that's is !

monty

Hi Monty good day...thanks for your help but I have one more question how can I upload the actual program that is running in the module using Hyperterminal?????
Is there any list of commands to talk with the module using hyperterminal????

I really appreciate all your help and I hope to help you some day.
THANKS
Segaauto

[segaauto]

Hello ,

COM521 Basic V1.1 english,

you can download here: http://shareplace.com/?CFD358516
or
http://plcforum.uz.ua//S5PEC21X.rar

Greetz

Thanks Corosop15 for your help.
My problem with this file is that it runs with versions lower than 7.0 of step5 and I have version 7.23.
I have been trying to get step 7 vesion 6.x but I can't find it.

Thanks a lot.
segaauto

[Corosop15]

Hello segaauto,

i have looked into all my archives, and i found 4 disks 3½'' with STEP5/ST for PC V6.03 and 3 disks 3½'' with STEP5/ST for PC V6.5 (Updating from V6.X).
It's running of old MS-DOS. I hope, the disks are o.k. If the disks are still readable, I upload it and you get a link for it.

Greetz
Corosop15

[Link]

Hello
here is the link for STEP5 Versions 6.X (MS-DOS), that i have.

http://shareplace.com/?4A2F7BBB4
or
http://plcforum.uz.ua//STEP5_V6.65.rar

Nice weekend

[segaauto]

Hi
I hope you are having a great day...

Thanks for this programs I'm downloading them and I will inform you tomorrow how was everything.

Thanks again

segaauto

[monty_burns_007]

i don't know if you can upload it back using hyperterminal.
But if the CP521 module is in stop : basic interpreter says: READY:
you can view the program with the basic LIST commando
maybe a copy paste action would do then

[segaauto]

I put the module in stop mode and I followed all your instructions but it never say ready: and I can't write in hyperterminal there is only a cursor blinking but when I try to write nothing happens what I try to write is not showed. But every time when I press a key the led RCV in the module blink and looks like reciving something but nothing happens.

I you have any idea of what is happening I will appreciate any comment.

Thanks.

segaauto

[segaauto]

I good day...

Thanks for the software i really appreciate it. Now my problem is that I can't install it because I have windows XP and the installer don't run.
I need to find a windows 95 or 98 in order to make it run or I don't know if there is a way to install it in windows XP.

Thanks a lot.
segaauto

[Corosop15]

Hello segaauto,

The software COM521 and STEP5 V6.X versions only run under MS-DOS.
They do not work under Windows XP.

If you need MS-DOS 6.22, then I can upload it to you. All I have only a german version.

Greetz
Corosop15

[monty_burns_007]

use a DOS or win95 vmware image....

[segaauto]

use a DOS or win95 vmware image....

I good day...
how can I get th vmware and the images of dos and win95???

Thanks
segaauto

[monty_burns_007]

Here are the vmwares....

For Dos version of Step5 you only need the dos vmware image.....

Dos 6.22: http://plcforum.uz.ua//V ... 2.zip.html
Win95: http://plcforum.uz.ua//VM_Win_95.rar default password win login: 1234567

[segaauto]

Hi everybody good day....Finally I install step5 in dos.
I had to use VirtualBox and install a dos image and install step 5.
BUT here an other problem.... step5 is asking for a device that has to be connected in the parallel port in order to run I thing is a kind of electronic old Licence and as usual I don't know what to do.

Comments are welcome.
segaauto